"Unable to lock the disk. Boot your computer from a Linux-based bootable media, and then try again."
I find myself in a real quandary. I'm trying to use an Acronis bootable USB drive to clone 7200 RPM HDD to a Samsung SSD. I’ve created bootable media with ATI 2019, 2020 and Cyber Home Protect. I get the same result when I boot from the flash drive. "Unable to lock the disk. Boot your computer from a Linux-based bootable media, and then try again." It’s been several years since I’ve had to restore an HDD or clone a drive. It could have been with ATI 2017. I’ve never had a problem before. I’ve put the 7200 HDD back in the Toshiba laptop. I’m in the process of cloning the 7200 HDD by using the installed ATI 2019 on Toshiba PC. The old PC is 4th GEN Intel i5, it’s slow, it’s been running 2hours and only 50% done. Which is why I wanted to use my DELL AIO with 11th Gen Intel i7. I see on the forum I’m not the only one having this problem. The video on using ATI 2021 had no sound or CC, no help! Any direction would be appreciated.


- Log in to post comments

Hi, I am getting the same "unable to lock disk" message. I am trying to clone a 1GB HDD to a 500GB Crucial SSD on a Win10 laptop. I have turned off Fast Boot in Win10 and have tried the HDD externally and internally but the message remains and I can't make any progress. I am booting from an Acronis rescue USB drive.
This is so frustrating as other SSD clones have been very straightforward.
What do I try next?
- Log in to post comments

Roy, welcome to these public User Forums.
Please see KB 56634: Acronis True Image: how to clone a disk - and review the step by step guide given there.
Note: the first section of the above KB document directs laptop users to KB 2931: How to clone a laptop hard drive - and has the following paragraph:
It is recommended to put the new drive in the laptop first, and connect the old drive via USB. Otherwise you will may not be able to boot from the new cloned drive, as Acronis True Image will apply a bootability fix to the new disk and adjust the boot settings of the target drive to boot from USB. If the new disk is inside the laptop, the boot settings will be automatically adjusted to boot from internal disk. As such, hard disk bays cannot be used for target disks. For example, if you have a target hard disk (i.e. the new disk to which you clone, and from which you intend to boot the machine) in a bay, and not physically inside the laptop, the target hard disk will be unbootable after the cloning.
Please see my earlier response to the original user who posted this topic.
- Log in to post comments

Hi Steve, thanks for the welcome and reply. I am happy to report that my clone has eventually been successful and the 'cannot lock drive' message was avoided.
I had tried several times with the target SSD in the machine but could not progress because of the message about locking the HDD source connected by SATA bridge cable. I followed the advice about turning off Win10 fast boot but that made no difference.
The solution for me was to boot from an Acronis rescue USB stick without the SATA bridge connected. I connected the source HDD with the SATA bridge after Acronis was up and running at the first screen. Cloning then went smoothly.
Regards
- Log in to post comments

Roy, thanks for sharing your resolution. When you say a SATA bridge, do you mean a USB to SATA adapter cable or are you using an eSATA connector to the HDD?
- Log in to post comments

Steve, the laptop is a few years old and doesn't have an e-SATA port. I connected the HDD with a USB to SATA cable.
- Log in to post comments

Dear Roy Parrott,
Thank you for the update. Can you please specify what product version are you talking about?
- Log in to post comments

Hi Daria, I'm not sure of the version number. I was using Acronis True Image for Crucial downloaded from Crucial site about two weeks ago. Crucial stated it was the 2021 version compatible with Win11, 10 and 8. I was using Win 10.
- Log in to post comments

Roy, sometimes OEM's have ancient builds - a few weeks back I downloaded the one for Kingston and it 19.0.0.5128 (the last set of digits is the build number) and the digital certificate was dated in 2016. In explorer, right click on the installation file, select properties: the Details Tab File Version gives the build, and you can get the date from the Digital signature tab.
About the same time, I downloaded the WD version, and it was dated 2021 and the build number was 39320
Ian
- Log in to post comments

Dear Roy Parrott,
Thank you for clarification. You can learn more in the article: Support for OEM Versions of Acronis Products | Knowledge Base
- Log in to post comments