Skip to main content

Cannot mount tib with new installation.

Thread needs solution

Clean install of windows 10 1909 and Acronis TI 2016 build 6595. Made several new backups. When I try to mount the new backups I get error message that TI 2016 cannot mount the .tib files. Other threads had patch TIB mount fix's for TI 2016 but the file no longer exists and was prob for older build.

So, bottom line is I don't even know if the backups are any good or if I can even restore from these. Getting a new M.2 nvme drive tomorrow and really need these and older backups to work. By the way - the new drive comes with Acronis cloning software.

Mounting was just my way of checking the backup files. They may be ok - but I'm kinda worried now.

0 Users found this helpful

OK, really confused now. The clean install in my post above is on a new 2TB HDD. Original drive is a 2TB SSD in my drive bay. Went back to the original drive, and files mount fine.

THEN, just got my new M.2 NVMe 2TB Sabrent. Registered and downloaded Acronis for Sabrent. Installed but had to uninstall TI 2016. Started Acronis for sabrent but said must have the M.2 drive installed on system. Well, of course it's not installed. If I install the M.2 SSD on my mother board and boot from my original SSD can I clone from the original bay mounted SSD with win 10 to the new M.2 Drive on my mother board. The literature says cant have both boot drives on the same machine.

If I can clone from the bay mounted SSD to the M.2 drive on the motherboard, will I be able to shut down the system when the clone is done, remove my bay mounted SSD and reboot from the M.2 drive?

I was hoping to mount the M.2 drive, boot Acronis from a thumb drive and restore to the new M.2 drive from an Acronis backup file I made of the 2TB HDD which is the brand new clean install of windows 10 with a bunch of installed programs I need. Is that possible? Are there sector size issues with that?

I spent several days setting up the clean install on the 2TB HDD. I did that because I could swap boot drives between the bay mounted SSD and the bay mounted HDD. The M.2 drive cannot be switched off in the BIOS so swapping boot drives will not work.

What are my options. Don't want to have to start from scratch with a clean install on the M.2 drive, and would prefer not to clone the existing bay mounted SSD (but will if that's what it takes). Please help

 

Steve, the ATI 2016 tib_mounter patch can still be downloaded if needed from the forum topic here. (I posted the original zip file myself and was able to download it still today).

On the second issue, the OEM versions of ATI have limitations which can cause them to not recognise drives if they are connected externally via an adapter or caddy etc.

To migrate from a normal SATA SSD or HDD to an NVMe M.2 SSD, the recommendation is to not use cloning, but to use Backup & Recovery, where the backup is made after first installing the new NVMe M.2 SSD so that Windows detects the hardware and installs any required device drivers, but leaving the SSD with nothing written to it / as unallocated space.

NVMe M.2 SSD drives normally require that Windows boots using UEFI / GPT, so you need to check that this is in place for the current HDD before attempting the migration.  You can check what BIOS mode is used by Windows by running the command: msinfo32 from Windows then looking for BIOS mode in the right panel of the report shown.

Once the above is done, then create the Windows PE version of the Acronis rescue media and test booting from this in UEFI mode to ensure that you can see all the installed drives plus your external backup drive.

At this point, I would recommend shutting down fully (press & hold a Shift key when clicking on Shutdown), then remove all drives except the NVMe SSD.

Boot from the Acronis WinPE rescue media in UEFI mode with the external backup drive connected.

Use the Tools > Add new disk to prepare the NVMe SSD using GPT partition scheme but leaving the drive as unallocated space.

Recover the Backup image from the HDD drive to the new SSD by selecting just the top Disk entry on the 'what to recover' panel (which will automatically select all partitions lower down).

When finished, shutdown and remove rescue media & external drive, then boot into Windows with only the NVMe SSD installed, and check all is working as expected.

If all is ok, then I would recommend connecting the original HDD via an external USB adapter and reformatting it before installing it back inside the computer.

KB 59877: Acronis True Image: how to distinguish between UEFI and Legacy BIOS boot modes of Acronis Bootable Media

When doing the restore of your backup, this needs to be done as a Disk & Partition restore and at the top Disk selection level.

Please see forum topic: [How to] recover an entire disk backup - and in particular the attached PDF document which shows a step-by-step tutorial for doing this type of recovery / restore.

Steve

Thanks for your help. Found a great deal on Acronis 2020 3 comp in my email, so I've switched to 2020. It mounted the .tib files just fine.

My 2tb HDD is UEFI / GPT with my clean install of Win 10 1909 and basic programs. My original SATA SSD is Legacy boot so I could never restore from my backups to the new M.2 anyway. Will need to use the legacy backups for data recovery only.

My usb boot is now made from TI 2020 so I assume it's UEFI, I've boot to that usb and it's listed in the boot selection as UEFI so that's pretty obvious.

From what you said above, do I need to first install my M.2 and then re-do my Acronis TI backup of the new 2TB HDD before I attempt a restore to the M.2? To confirm what you said, this adds additional files for the M.2 to the backup.??

From that point it sounds like I just unhook all my drives except the Backup 4TB HDD and boot from the USB. Look for "Add new disk" to prepare a GPT partition on the M.2 drive, and then restore to the M.2.

Shutdown --- unhook the 4TB backup drive - then reboot to the M.2 alone.

Hope that's all correct.

Any step by step M.2 tutorial for TI 2020?

Thanks

PS, just looked thru your pdf and looks very much the same as 2020. (I did a restore of the 2TB HDD using TI 2020 yesterday that in fact solved a problem for me) Thanks again for your help.

Steve, all the Acronis rescue media is capable of booting in UEFI and Legacy modes as per KB 59877 referenced in my previous post.

It is better to install the NVMe M.2 SSD and leave it 'empty' then reboot Windows so that it detects that new hardware has been installed and installs any new device drivers required for the new hardware. 

After the above, then create a new full disk backup of the working HDD so that this then includes the changes introduced by adding the new hardware.

Once you have the new backup, then as stated previously, reduce the system to having only the new M.2 SSD then boot from the rescue media with the backup drive connected, and restore back to the SSD.

See the attached zip file with screen shots from earlier this year when I upgraded my own NVMe M.2 SSD to a larger one in my laptop which is similar in principle to what you will be doing.

Attachment Size
536892-183480.zip 611.43 KB