CLONING INTERNAL HDD TO EXTERNAL USB HDD - DESTINATION HDD REPORTED TOO SMALL
I have a HP IQ820 - Touchsmart with an internal 640gb HDD.
I wish to clone this internal HDD to a 1.5tb HDD mounted in an external USB dock.
I am using True Image Home 2010.
I select Clone.
It recognises both HDD.
I select the internal HDD as Source.
I then select the larger external HDD as Destination.
It the advises it cannot continue because Destination HDD is too small.
Help please.

- Log in to post comments

I would also try what is referenced as a "reverse clone". This type procedure should also be done when booted from the TI Rescue CD.
A reverse clone is:
1. Remove the source disk and place it in an alternate location such as your docking unit.
2. Install the target in its intended boot position.
3. Perform the clone but keep any recovery partitions the same size. (Manual cloning mode gives the user control very assigning sizes to the partitions.
After cloning, shutdown and remove the source disk and complete remove the docking unit from the computer. There have been reports of the computer being connected to a docking unit during first boot has caused grief.
I am not familiar with your particular model computer.
- Log in to post comments

The disc is brand new and I have checked it for errors and it has come out clean.
Curiously, I have done a manual 'as is' clone which works but this does not take into account the larger HDD and therefore does not proportion the partition sizes. I suppose I could take the 'as is' clone and then use another program to adjust the partion sizes. But it is still a mystery why the ACRONIS clone / automatic does not work. I think I may try the reverse clone!
- Log in to post comments

Whatever method you try, try running a simulation using the manual mode and see what is happening. With TrueImage, it is practice up to the point where my must choose to Proceed or Cancel. You choose Cancel to stop any further testing. If you press proceed, it is too late to stop the practice as the procedure will have been activated. You should choose the manual mode so you have control over the partition sizes. Have you checked the source disk for errors also.
- Log in to post comments

I have an internal hard drive I would like to clone to a smaller external usb drive to keep & maintain as a "picture" of the working OS installation. The internal hard drive is partitioned in two logical drives, one active and containing the Operating System (Windows 7 Pro x32), the other D:\ is a "RECOVERY_DRIVE" partition set up by HP for restoring the system in the event of a major system failure on the C: drive. As things sit now, the active C: drive is @ 465 Gig in size of which @ 45 gig is currently used by the OS setup. The secondary D:\ partition is @ 14 gig in size of which the recovery files take up @ 7 gig of space.
The USB drive I am trying to clone the above to is @ 143 gig in size, and currently empty. When plugged into the desktop, the external USB connection Hitachi drive is listed as Drive L:
When I try to run ATI 2010, Acronis
a. Starts and sees both drive 1 (the 500 gig internal drive containing both the active C:\ and D:\ recovery partitions; as well as the USB attached empty Hitachi 160 Gig drive. The 160 gig USB drive is listed by ATI as Drive 8.
b. I can select drive 1, the C: & D: partitions on the internal 500 gig drive as the drive to clone. However Acronis will not let me proceed to "select" a destination drive - the "next" button remains grayed out & inactive, though ATI "sees" the USB drive as ATI drive 8.
c. I have run check disk on both drives
d. Interesting, FWIW, if after ATI is running I open Explorer and ask it for the L:\ drives properties, Explorer reports the drive as "full" as soon as ATI starts "processing" the select source option / destination.
How do I get ATI to let me clone @ 51 gig of used space on the 500 gig primary drive to the empty @ 143 gig USB drive? Seems to me there should be more than enough space on the 143 gig USB drive to be able to hold the two primary drive partitions.
Thanks, Mike P
- Log in to post comments

You say you have Windows 7 right? So before you run the "clone", use Windows "Disk Management" to reduce the free space on both partitions C & D as far as windows will alllow (you can always put them back to what they were when you're done). You shouldn't have to get another program to adjust the partitions... Then try to run the clone... You see, ATI thinks that you are trying to clone 479GB onto a a drive that is only 143GB. Do the math. You see normally when someone clones a disk, it is because they have exhausted the free space in their current drive and need to clone to a larger one, so I'm not sure, but I think ATI is thinking you want to clone all of your partitions onto the new SMALLER drive, and it just doesn't work. That is why you should make them smaller so they will fit.
- Log in to post comments