Acronis удаляет данные во время клонирования диска
Второй раз уже Acronis во время клонирования диска удаляет все файлы с основного. В чем причина и как избегать такие проблемы.
Allegato | Dimensione |
---|---|
IMG_20200304_184905.jpg | 2.49 MB |


- Accedi per poter commentare

Как использовать я знаю. Так же я знаю, для чего нужно клонирование и для чего нужно резервное копирование. Мне не понятно, почему клонирование трет диск.
Не пойму как удалить сообщение.
- Accedi per poter commentare

Steve Smith wrote:Welcome to these public User forums.
Please see KB 1540: Разница между резервным копированием и Disk Clone
Any disk clone will always delete the contents of the target disk drive in preparation for recreating the partition structure and contents from the source disk drive.
Как использовать я знаю. Так же я знаю, для чего нужно клонирование и для чего нужно резервное копирование. Мне не понятно, почему клонирование трет диск.
- Accedi per poter commentare

Cloning has to delete everything on the target disk drive in order to prepare that drive to be identical to the source disk drive. It is a 1:1 relationship between the two disk drives in order to create a duplicate copy of the source on the target. So by its nature it will delete everything on that target drive.
What exactly are you trying to do here?
- Accedi per poter commentare

Steve Smith wrote:Cloning has to delete everything on the target disk drive in order to prepare that drive to be identical to the source disk drive. It is a 1:1 relationship between the two disk drives in order to create a duplicate copy of the source on the target. So by its nature it will delete everything on that target drive.
What exactly are you trying to do here?
Проблема в том что он удаляет данные на исходном диске. А должен удалять на диске на который переносим данные.
- Accedi per poter commentare

The problem is that it deletes the data on the source disk. And it must delete on the disk to which we transfer data.
Denis, no data should be deleted on the source disk when doing cloning (or backup).
I would strongly recommend making a full Disk & Partitions backup of the source disk then using that backup to restore to the new disk instead of using cloning.
- Backup the source disk to an external disk drive.
- Create the Acronis rescue media (on a USB stick or DVD).
- Shutdown the computer and test that you can boot correctly from the rescue media.
Note: this needs to be matching how your Windows OS boots - use the command:
msinfo32 from the Windows desktop to check the BIOS mode used by Windows, i.e. this will be either UEFI or Legacy / the disk name. - Shutdown and remove the source disk, replace this by the new drive, putting the source drive aside where it cannot be changed.
- Boot from the rescue media with your external backup drive connected.
- Recover the backup image to the new drive.
- Shutdown, remove the rescue media and external drive.
- Boot into Windows from the new drive.
All of the above assumes that you are going to use the new drive in the computer where you are working with.
Денис, никакие данные не должны быть удалены на исходном диске при выполнении клонирования (или резервного копирования).
Я настоятельно рекомендую сделать полную резервную копию диска и разделов исходного диска, а затем использовать эту резервную копию для восстановления на новый диск вместо клонирования.
Сделайте резервную копию исходного диска на внешний диск.
Создайте аварийный носитель Acronis (на USB-накопителе или DVD-диске).
Выключите компьютер и проверьте правильность загрузки с загрузочного носителя.
Примечание: это должно соответствовать тому, как загружается ваша ОС Windows - используйте команду:
msinfo32 с рабочего стола Windows для проверки режима BIOS, используемого Windows, то есть это будет либо UEFI, либо Legacy / имя диска.
Выключите и удалите исходный диск, замените его новым диском, отложив исходный диск там, где его нельзя заменить.
Загрузитесь с загрузочного носителя с подключенным внешним резервным диском.
Восстановите образ резервной копии на новый диск.
Выключите, извлеките загрузочный носитель и внешний диск.
Загрузитесь в Windows с нового диска.Все вышеперечисленное предполагает, что вы собираетесь использовать новый диск на компьютере, с которым вы работаете.
- Accedi per poter commentare