Migrate Windows 7 OS from non-RAID to RAID

Thread needs solution
truwrikodrorowrelupicugojestutroclulachosaswunuhospikigawakijosaswenomaruclojeueclikaspedrubewidebrisubrohutrurifruuagothunugekedrumucisiuobrobrecrupeslapuswosluprothethibakaslechurathikucli
Beginner
Contributions: 1
Commentaires: 2

I'm new to Acronis with True Image Home 2011

I want to migrate a functioning Windows 7 OS from a non-RAID environment to a RAID 10 configuration without doing a fresh Windows install.

The RAID drivers needed are on a USB thumb drive.

What procedure is recommended to accomplish this goal and please be specific?

Do I need to purchase Plus Pack to accomplish my goal?

My total experience with Acronis:
I've used Acronis's clone capability successfully before to migrate a functioning RAID 10 Win7 system to larger disk drives from smaller drives but that system already had the drivers and the only hardware change was the larger disk drives. Everything else was unchanged.

mar 12/04/2011 - 13:56
0 Users found this helpful
truwrikodrorowrelupicugojestutroclulachosaswunuhospikigawakijosaswenomaruclojeueclikaspedrubewidebrisubrohutrurifruuagothunugekedrumucisiuobrobrecrupeslapuswosluprothethibakaslechurathikucli
Forum Star
Contributions: 45
Commentaires: 4263

In the tests and conversions I've done, the RAID drivers generally need to already be installed to allow you to just restore to the RAID and have it work. For example, while still using the single drive, install the RAID drivers (may need to enable RAID mode in BIOS first), reboot into Windows (to make sure drivers are fully installed), image the drive, setup the RAID drives, restore image to RAID.

This method may not work due to a number of factors. However, it's free to try. Sometimes enabling RAID mode can cause the system to not boot correctly and sometimes the drivers won't want to install because there aren't any RAID drives.

These two threads should give you some ideas on the procedure:
Non Raid Image to Raid 0 config question
First time user of ATI Home 2009 please help!!!!!

The Plus Pack should allow you to do it also.

mar 12/04/2011 - 15:52
truwrikodrorowrelupicugojestutroclulachosaswunuhospikigawakijosaswenomaruclojeueclikaspedrubewidebrisubrohutrurifruuagothunugekedrumucisiuobrobrecrupeslapuswosluprothethibakaslechurathikucli
Beginner
Contributions: 1
Commentaires: 2

Thanks...

I tried your first suggestion both with and without RAID enabled... both were a no-go.

But I'm cloning my system drive to an external and then cloning it back.

Is cloning the right way to do it or is another approach better?

I'll look into the other postings as suggested.

mar 12/04/2011 - 16:04
truwrikodrorowrelupicugojestutroclulachosaswunuhospikigawakijosaswenomaruclojeueclikaspedrubewidebrisubrohutrurifruuagothunugekedrumucisiuobrobrecrupeslapuswosluprothethibakaslechurathikucli
Forum Star
Contributions: 45
Commentaires: 4263

I prefer imaging to cloning since you have a backup and the source drive doesn't need to be connected. However, from the standpoint of getting a booting system with RAID it shouldn't matter.

When what you tried didn't work, did you get a 0x7B BSOD or some other error?

If you have enough connectors and drives, you can setup two drives in RAID (0 or 1, doesn't matter) while still booting from the single drive. Install the RAID drivers and make sure you can access the RAID drive. This would let you know for sure the drivers installed. Then reconfigure the system for RAID 10 and restore or clone to it (image the single drive before breaking the system if planning on restoring instead of cloning).

mar 12/04/2011 - 16:40
truwrikodrorowrelupicugojestutroclulachosaswunuhospikigawakijosaswenomaruclojeueclikaspedrubewidebrisubrohutrurifruuagothunugekedrumucisiuobrobrecrupeslapuswosluprothethibakaslechurathikucli
Beginner
Contributions: 1
Commentaires: 2

The clone back into the RAIDed system works fine except that the RAID array looks incomplete before starting.

However, upon reboot Win7 crashes with the blue screen of death. Reboot does not help and Windows Repair can't fix it even though it can see the OS.

mar 12/04/2011 - 18:04
truwrikodrorowrelupicugojestutroclulachosaswunuhospikigawakijosaswenomaruclojeueclikaspedrubewidebrisubrohutrurifruuagothunugekedrumucisiuobrobrecrupeslapuswosluprothethibakaslechurathikucli
Forum Star
Contributions: 45
Commentaires: 4263

What do you mean... the RAID array looks incomplete before starting ?

mar 12/04/2011 - 18:10